Hexagon Stainless Steel Push Rod M3 X 1.5'' (The U.S System)

This device allows you to safely and remotely kill your electronic ignition equipped
engine your transmitter.igniton system is Fiber Optically Coupled to isolate your
igniton system from your radio system .(No Interference!!)

(Battery Eliminator Circuitry)
The kill swith not including BEC function

Rcexl Plug Holder

The price is for 20pcs

The first Iridium Spark Plug for RC Model Engine in the world.
Good Quality and Cheap Price!

1:Use P1C16f628a microcontrollers
2：Do not need batteries, power from the ignition
3: Standard Futaba Plug(Black-negative Red-Postive and White-Signal)
4:Using high-brightness LED digital tube
5:Input voltage range: 3.5V -8.4V
6:Current consumption 25mA-60mA
7:Mini tachometer indicates up to 30000rpm
8:Actual RPM=Display digital *10
9:Body size:41mm L*17mm W*12mm H
10: Window size:30mm L*15mm H
11:Weight: 8.5g(0.3OZ)

Instructions:
1:The Y wiring tandem between in the Hall sensor and the ignition
2: The tachometer plug the other end with Y wire
3:Connected to ignition power supply and can be displayed

Note: That connecting plugs do reinforcement.To preven vibration. the hall
sonsor& tachmoter wire leave from the ignition high-voltage wire, And re-
ceiver wires over 30cm

Connection tachometer is not recommended after the use of the flight, Best
to remove the Y wire to restore the original sensor connection

If ignition have an additional tachometer pinout,You must be connected to
dedicated tachometer signal wire

Video-1:

Video-2

Phoenix 9 in 1 Simulator,Support phoenix 3.0 after updating.
Compatible: Phoenix 1.0 / 2.5/ 3.0, Realflight G2 /G4 / G4.5, Reflex XTR .Aerofly.FMS

Package Include :
JR Audio cable 1PCS
Futaba convert cables 2pcs
Esky convert cable 1pcs
DVD 2pcs
USB dog 1pcs

T-Plus battery connecter Price is for 10 Pairs

Mechanical Specification

Size ：A：40.2mm B：20.1mm C：38.8mm D：48.0mm E：10mm
Weight：57.5g （2.03oz）
Gear type:Titanium Gear
Limit angle :210�
Bearing： 2 Ball bearings
Horn gear spline ： 25T
Horn type ：Plastic,POM
Case：Engineering plastics & Aluminium
Connector wire ：300mm
Motor： Coreless motor
Splash water resistance：Yes
Application: suitable for futaba 25T servo arms

Apply Environmental Condition
Storage Temperature Range：-30℃～80℃
Operating Temperature Range：-25℃～70℃

Standard Test Environment
Temperature range：25℃ ±5℃
Humidity range：65%±10%

Electrical Specification (Function of the Performance)

The Drawings

Servo Performance curve （at 7.2V）

Canopy lock

Specs:2300 mah - RX 2 cell 6.6volt - 2s1p Max Discharge Continuous - 30c
Weight:150g With Futaba/JR receiver connector
Battery Size:71*26.5*52.5mm
Length of cables: 62mm/136mm

Dimensions: 1.57" x 0.79" x 1.44" (40 x 20 x 36.5mm)
Weight: 1.44oz / 39g ( Servo Net Weight Only )
Operating Speed (4.8V no load) : 0.14sec / 60 degrees
Operating Speed (6.0V no load) : 0.11sec / 60 degrees
Stall Torque (4.8V): (5.2kg/cm)
Stall Torque (6.0V): (6kg/cm)
Temperature Range: -30 to +60 Degree C
Dead Band Width: 4usec
Operation Voltage: 4.8 - 6 Volts

Special plug for fuel tank （use for Gasoline / petrol）

Voltage Range:3V-30V
L*W*H=24*20*12
electric current :4-8mA
Net Weight: 6g
Suitable All of the Battery! Good Quality and Cheap price.

Cooling fin for airplane cowl 75×60×0.5mm

Size：7*4mm
Outside diameter: 7mm
Inside diameter:4mm
Color: Yellow and blue both are in availble.
This is corrosion resistant fuel line.We have tested this gas line in 93# petrol
more than 6 month,No Metamorphose.we can cut it for you according to your
request.
Unit: meter
Material: TPU (imported from Taiwan)

Specs:
2300 mah - RX 2 cell 6.6volt - 2s1p
Max Discharge Continuous - 30c
Weight:150g
With Deans Connector
Battery Size:71*26.5*52.5mm
Length of cables: 62mm/136mm

The gear pump we are selling is the best seller of our company. Instead of using
expensive imported smoke pump, DIY the fuel pump reflects high cost performance.
However the RC fans leave much to be desired when using it since this fuel pump
was used as water pump.
At present, there are two problems revealed: 1. the original plastic gear is delicate;
2. long time usage easily cause oil leak. Last year, we have developed a set of metal
gear according to the feedbacks of our customers, with which we solve the problem
of delicate. This time, we present a full set of
DIY accessories to solve the problem of oil leak once for all.

Related parts:

20A ESC:http://www.sdshobby.net/20a-brushed-esc-for-smoke-pump-
system-p-4070.html

Special tool:http://www.sdshobby.net/metal-gear-sets-only-for-smoke-
pump-p-4071.html

Electric Capacity:http://www.sdshobby.net/electric-capacity-for-smoke-pump3pcsbag-p-4072.html

1.Material
Tyre :PU Rubber
Wheel hub: ADZ12 ALUMINUM Alloy

2.Advantage
a, Anti-Corrosion
b, Abrasion resistant

3.Workmanship
a, Wheel hub: Casting---->CNC ----->Ageing treatment --->Shot Blasting
b,Tyre: Foaming Freatment

Screw: 4pcs

Allen key: 1pcs

Work Voltage :3.6V-6V
Need ESC:http://www.sdshobby.net/20a-brushed-esc-for-smoke-pump-system-p-4070.html

Work Voltage :3.6V-6V
Need ESC:http://www.sdshobby.net/20a-brushed-esc-for-smoke-pump-system-p-4070.html

Price is for 10 Pairs

Function of Performance:
☆METAL GEAR with Ultra-Torque
performance for Mon ster truck.
☆0.18sec/60�at 6.0V
☆16kg-cm at 6.0V
☆40.7x20x42.4mm
☆Weight:61g
Storage Temperature:-20℃～60℃
Operating Temperature:-10℃～50℃
Operating Voltage:4.5～6.0V

Servo Cable Holder
The price is for 20pcs
(This product sent at random color.)

Special Pitts muffler for DLE50 / DLE55 / DA50 / DLA56 / GP50R/ EME55

Round Fuel Dot for airplane

Character:
1. New generation fuel pump with compact size
2. Double injection, using TPR material that has a comfortable feel
3. Improved gear mesh and make the large flow rate 18cc/sec
4. Advanced pump unit design, glow fuels and gasoline are both compatible
5. Includes filter fuel nozzle and 19¡¨ silicon fuel tubing

For 2C and 4C Nitro Engine.

4.8V-6V JR Futaba comatible

Cooling fin for airplane cowl 120×100×0.5mm

Round Fuel Dot for airplane

Futaba TX Belt for radio system

Size: 67*17*32mm ( Length*Width*Height)

Gross weight: 100g

Compatible with Futaba and JR

HWFJ150	Heavy duty 22# Twisted Wire 150mm JR/Futaba
HWFJ300	Heavy duty 22# Twisted Wire 300mm JR/Futaba
HWFJ450	Heavy duty 22# Twisted Wire 450mm JR/Futaba
HWFJ600	Heavy duty 22# Twisted Wire 600mm JR/Futaba
HWFJ750	Heavy duty 22# Twisted Wire 750mm JR/Futaba
HWFJ1000	Heavy duty 22# Twisted Wire 1000mm JR/Futaba

Price for 10pcs

2/3A Stick Pack for Receiver Futaba connector

This spinner can be usded for DLE20 & DLE55 engine, MLD28, DA50 and EV054 engines.

Wheel Shaft Bolt M8×Φ4×50mm

Twin Power Switch With Fuel Dot-Blue Color

Oil Drum Connector

The price is for 5pcs

Pitts Muffler for 26-30cc plane,For example,DLE-30,CRRC GF26i 26CC,etc.

10 Pairs * 4.0MM babana plug connector

3 way T joint

1.One control CDI Ignition,another control electric system in the Gas Airplane.
2.Metal Case

XQ-Power Digital Servo S4016D 16KG/57.5g with Titanium Gear/Alu Case
Application: suitable for futaba 25T servo arms

Big 3 way T joint with Fuel Filter

Rxcel ignitons are supplied as standard epuipment on many RC engines and rep-
airs or modifications may require the static timing point to be reset or checked.

The kit will allow you to check and wdt your static timing point as specified ,it co-
mes with a LED SHOW and audible(Buzzer) signals.

Rcecl ignition when checking over the magnet in trigger point .is to stop the light –
emitting LED and audible buzzer to stop the moment when the igniton spark.

This kit can also tbe used to check the correct peration of the hall sensor and de
termine correct magnet orientation.

Not indluded CR2032 battery&hall Sensor .

Rcexl in CM6 Spark Plug Cap Spring(TWO pcs)

This is a timing and testing kit for RC Gas/Petrol engines using CDI ignition .

This kit,will allow you to check ignition Working conditions.

Without the need to start the engine.

Analog engine speed in between the 400RPM-20000RPM,Can be used to check
radio interferences ,and the radio range check

Full instructions supplied.

WARNING

This unit will fire the spark plug, and if still fitted to the engine, any fuel vapor still inside the engine may ignite and rotate the propeller and/or cause flame/heat from the exhaust.

DO NOT TOUCH SPARK PLUG

When this is running or you will receive an electric shock!

1. Turn ignition OFF

2. Ensure spark plug is properly seated into ignition cap. Spark plug must be used or damage to ignition module is possible.

3. Use dial on tester to set desired RPM – this will simulate a hall sensor being triggered and will fire the ignition/Spark plug at this RPM setting.

4. Disconnect hall sensor from ignition and connect tester with correct polarity to the ignition sensor lead coming out of the CDI

See photo below for correct connection – note wire colors.

5. Turn on ignition power. The LED on the tester will light if connected correctly, and the spark plug will start firing at the set RPM. You can adjust the dial to increase/decrease the RPM. If LED will not light the tester may be faulty or the sensor/wiring is not compatible.

6. If plug is firing you are now simulating a running engine/ignition and can complete range tests for ignition noise etc without actually running the engine. If the spark plug does not fire, check above connections to tester first. Otherwise

• Check ignition battery is good. Do not use an old pack

• Check all wiring and leads are connected correctly and not damaged.

• Check/Replace spark plug

• If your ignition still does not fire you may have a faulty ignition or tester

• If Ignition fires OK with tester, but not when connected to sensor then your hall/pickup sensor is likely to be faulty or too far from magnet or incorrect orientation to magnet (flip sensor 180 degrees to test)

7. If ignition runs OK at low RPM, but breaks down at higher RPM try another battery first and check wiring to ignition unit (try battery direct to ignition – bypass switch etc)

This can also be caused by short in plug cap/s or faulty ignition module

8. When finished testing turn off ignition power. Disconnect tester and reconnect ignition module to sensor.

3.5mm male connectors
3.5mm female connectors

Price is for 10 pairs

The price is for 1 unit only !
Weight:205g

For Ф6*3/ Ф7*4 Fuel line

This spinner can be usded for DLE20 & DLE55 & DLE30 engine, MLD28, DA50 and EV054 engines.

Plug-in Epoxy Control Horn Φ3*1.5*17.5*25*H38mm

Air filter for 20-60cc Gas Engine

This is the Futaba S3003 Standard Servo.
This basic servo is used in cars, boats, or where standard servos are used.
This is the replacement for the following servos, S138,S148,S22,S38 and S12.
This servo can produce high-current draw from your batteries.
If using NiMH or LiPo batteries, make sure they are capable of delivering sufficient
amps.

SPECS: Speed: 0.23 sec/60� @ 4.8V
0.19 sec/60� @ 6V
Torque: 44 oz-in (3.2 kg-cm) @ 4.8V
57 oz-in (4.1 kg-cm) @ 6V
Dimensions: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16")
(40 x 20 x 36mm)
Weight: 1.3oz (1-5/16oz) (37g)
Connector: "J" type with approx. 5" lead

Special muffler canister for DLE30

10 Pairs* Six Pin Connectors

The price is for 10pcs

Round Fuel Dot for airplane

10Pcs *Heavy duty 22# Twisted Wire 150mm JR Color
Compatible with Futaba and JR

HWFJ150	Heavy duty 22# Twisted Wire 150mm JR/Futaba
HWFJ300	Heavy duty 22# Twisted Wire 300mm JR/Futaba
HWFJ450	Heavy duty 22# Twisted Wire 450mm JR/Futaba
HWFJ600	Heavy duty 22# Twisted Wire 600mm JR/Futaba
HWFJ750	Heavy duty 22# Twisted Wire 750mm JR/Futaba
HWFJ1000	Heavy duty 22# Twisted Wire 1000mm JR/Futaba

Product Name: USB Simulator Cable
Minimum system requirements:
-100% Pentium III or AMD Athlon/64 compatible processor with at least 800Mhz
-128MB RAM
-1GB free hard disc memory
-CD-ROM drive
-Open GL compatible graphic card with at least 64MB
-100% DirectX compatible sound card
-Windows 98,ME /2000/XP with DirectX version
-9.0b or highter
-A free USB port and a trainer output on your transmitter

Recommended system requirements:
-100% Pentium IV or AMD 64 compatible processor with at least 1600Mhz
-256MB RAM
-CD-ROM drive
-OpenGL compatible graphic card with at least 128MB
Pleaser note: On a system with only minimum system requirements,the
performance strongly depends on the currently loaded model and scenery.

4pcsx Carbon Fiber Washer 18mmx5mmx4mm

Outer diameter: 18mm

Inner diameter: 5mm

Thickness: 4mm